Skip to content

EDEL · Platform

Edel K2 and K3 controllers — spare parts and variants

K2 is the range of Edel electronic control panels. It comes in several publications depending on the installation’s drive type, each corresponding to its own diagram and wiring.

All variants accept simplex, duplex, triplex and quadruplex configurations, for 29 to 32 levels depending on the version. Configuration is carried out with a dedicated programming console.

Two variants are worth distinguishing: ECO+, whose controller mounts on the door frame for installations without a machine room, and SLIM, which pairs a Fuji FRENIC Lift drive with an asynchronous motor where the other gearless versions use a synchronous motor.

K3 is the next generation. The shaft accessories — bistable supports, detectors and level rollers — are specific to it and are not interchangeable with those of K2.

Technical sheet

Technical specifications

Configurations
Simplex, duplex, triplex, quadruplex · 29 levels, 32 levels on the SLIM version
Drives used
Fuji FRENIC Lift on the gearless, ECO+ and SLIM versions
Power ranges
From 5.5 HP to 25 HP at 400 V AC on drive versions
Installation versions
Standard on machine cabinet · Pre-assembled (EDEL plate 64410) · Advanced EN 81-20 · ECO+: controller on door frame
Accepted drives
Two-speed asynchronous · 3VF asynchronous with drive · Gearless synchronous · Oleodynamic
Position feedback
Absolute or incremental encoder · Speed change by magnets, screens or timing
Console menu
Lift status · Configuration · Parameter programming · Faults · Maintenance · Date and time · Inputs / outputs
Configurable options
Magnet counting (up/down, stop/speed change) · Auxiliary relays: car lighting, fan · Keypad lock · Double access, including selective · Floor configuration · Multiplex · Audio · Non-stop · Arrows · Encoder · Firefighters
Door reopening
Contact, photocell 1 or photocell 2
Connections in the car
Pendant in the controller or inspection box · Safety devices in the car · Governor in the car · Detectors, bistables and shaft magnets

Comparison of K2 variants

VariantPublicationEditionLevelsPowerDriveMotor
Two speedsK2 64200-00202/2009———Two-speed asynchronous
With driveK2 643VF-00502/200929——3VF asynchronous
GearlessK2 643VFG-00706/2011—5.5 to 25 HP / 400 VFuji FRENIC LiftGearless synchronous
ECO+ — on door frameK2 ECO+ 00110/2011295.5 to 25 HP / 400 VFuji FRENIC LiftGearless synchronous
SLIMK2 SLIM-A 00104/2013325.5 to 25 HP / 400 VFuji FRENIC LiftAsynchronous
OleodynamicK2 64230-00203/2009———Hydraulic

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Control cabinet

It contains the K2 panel itself, the drive when the traction requires it, and the associated boards. The reference publication depends on the type of drive.

Related parts: board · cabinet · controller · drive

Shaft and selection

Bistable supports, level detectors and rollers handle the car’s position marking. K3 supports differ from those of K2.

Related parts: bistable · detector · support

Car and landings

Button panels, indicators and signalling connected to the controller.

Related parts: button · display · faceplate

Machinery

Two-speed asynchronous motor, drive motor or synchronous gearless machine depending on the chosen variant.

Related parts: motor · encoder · brake

Points of attention

  • First identify the publication of your panel: 64200-002 for two speeds, 643VF-005 for drive, 643VFG-007 for gearless, ECO+ 001 on door frame, SLIM-A 001, or 64230-002 for oleodynamic. Wiring and boards differ between these variants.
  • Do not confuse gearless and SLIM: both use a Fuji FRENIC Lift drive, but the first drives a synchronous motor and the second an asynchronous motor. The setup and encoder feedback have nothing in common.
  • K3 shaft accessories do not replace those of K2: check the generation before ordering a bistable or detector support.
  • The type of encoder — absolute or incremental — determines the choice of interface board as well as the connector to use.
  • Note the panel number and software version shown in the installation’s documentation: they appear on the first page of the manual and determine compatibility.
  • The programming console is required to restore the settings after replacing a control board. The “Lift status” menu shows the software version and configuration number in place.
  • On pre-assembled installations, the pendant connects either directly to the controller or to the inspection box: check the configuration before ordering a harness.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all Edel K2 / K3 parts in the catalogue ↗

Source of the specifications: Edel K2 publications 64200-002 (02/2009), K2 643VF-005 (02/2009), K2 643VFG-007 (06/2011), K2 ECO+ 001 (10/2011), K2 SLIM-A 001 (04/2013), K2 64230-002 (03/2009), pre-assembled installation and Advanced EN 81-20 manuals, and the K2 programming console manual (R05). Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about Edel K2 / K3

What is an Edel K2 controller?

K2 is the range of Edel electronic control panels. It drives the motor, doors, signalling and safety devices of the lift. It exists in four variants depending on the drive: two speeds, frequency drive, synchronous gearless and oleodynamic.

What is the difference between K2 and K3?

K3 is the generation that succeeds K2. The shaft accessories — bistable supports, detectors and level rollers — are specific to each generation and are not interchangeable. Check the generation of your installation before any order.

How many levels does a K2 controller serve?

The drive variants and ECO+ serve up to 29 levels, the SLIM version up to 32. All accept simplex, duplex, triplex and quadruplex configurations.

Which drive equips the K2 versions?

The gearless, ECO+ and SLIM variants all use a Fuji FRENIC Lift drive, for powers from 5.5 to 25 HP at 400 V AC. The difference lies in the motor: gearless synchronous for the first two, asynchronous for SLIM. The encoder type, absolute or incremental, must be specified in every case.

What is the K2 ECO+ version?

ECO+ is the variant whose controller mounts on the door frame, intended for installations without a machine room. It pairs a Fuji FRENIC Lift drive with a gearless synchronous motor and serves up to 29 levels.

How do I identify the right Edel part?

Note the panel publication, the panel number and the software version, as well as the reference shown on the board to replace. A photo of the board and its markings allows KMY to confirm the match.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote