Skip to content

SODIMAS · Platform

SODIMAS NG02, NG12, NG120 and NG240 controllers

NG refers to the generations of SODIMAS controllers that preceded QI Touch. Four are commonly found in the installed base: NG02, NG12, NG120 and NG240, the latter being the most recent and the most represented in the catalogue.

Each generation comes in several drive types, and it is the associated drive that distinguishes the versions: two speeds without drive, Altivar ATV31, ATV58 or ATV71, V3F10, or Fuji FRENIC Lift on the most recent versions. The hydraulic versions form a separate branch.

These controllers remain supported and are the subject of conversion kits — notably the switch from an asynchronous drive to a gearless synchronous machine on a Fuji FRENIC Lift drive.

Technical sheet

Technical specifications

Generations encountered
NG02 · NG12 · NG120 · NG240
NG02 variants
Two speeds · Altivar ATV58 · Hydraulic
NG12 variants
Two speeds · Altivar ATV31 · Altivar ATV58 · Altivar ATV71 in 5.5 kW and 7.5 kW · V3F10 · Hydraulic
NG120 variant
Fuji FRENIC Lift drive
Motherboard — 2012 documentation
32-bit microprocessor clocked at 100 MHz · RS485 port, CAN Open bus and Ethernet · Incremental or absolute counting · Built-in mini web server · 24 levels adjustable depending on the controller · Asynchronous VVVF or gearless synchronous traction · Multi-pump hydraulic control · 1 or 2 accesses, multi-door
Announced compliance
Class A energy eco-design (VDI 4707) · A3 and EN 81-21 compliance · Prepared for remote monitoring
Conversion to synchronous
Asynchronous-to-synchronous replacement kit on Fuji FRENIC Lift · KM4 bypass contactor to fit in the power cabinet · Additional contactor and rectifier above 11 kW · Encoder board to connect to the drive · Brake voltage to take from the transformer depending on the motor

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Power cabinet

It houses the NG motherboard, the variant-specific drive and the DTU power supply box. The layout diagram differs depending on the generation.

Related parts: board · cabinet · drive · DTU panel

Shaft wiring

The combined wiring on CAN Open bus links the controller to the landings and the selection devices. It is the family most represented in the catalogue for these generations.

Related parts: wiring · shaft duct · connector

Selection and position

Counting is incremental or absolute depending on the chosen configuration.

Related parts: sensor · bistable · encoder

Car and landings

Button panels, indicators and signalling connected to the controller.

Related parts: button · display · faceplate

Points of attention

  • Identify the exact generation — NG02, NG12, NG120 or NG240 — before any order: boards and wiring are not interchangeable between them.
  • Also state the drive variant: ATV31, ATV58, ATV71, V3F10 or Fuji FRENIC Lift. Two cabinets of the same generation can differ completely on this point.
  • The hydraulic versions form a separate branch, with their own diagram and their own wiring.
  • For a conversion to a gearless synchronous machine, the layout diagram of the bypass contactor depends on the controller in place: it differs between NG120, NG240 and QI.
  • Beyond 11 kW, the synchronous conversion kit requires an additional contactor and rectifier.
  • These generations precede QI Touch: if you are considering a full modernisation rather than a like-for-like replacement, the question of moving to QI Touch deserves to be asked.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all Manœuvres NG SODIMAS parts in the catalogue ↗

Source of the specifications: SODIMAS documentation: manual NG01/NG02 ref. NBE041, motherboard documentation ref. 27 000 007 (09/2012), synchronous conversion manual ref. 48809 / 27 100 007 (13/12/2023) and NG02 and NG12 variant diagrams. Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about SODIMAS NG controllers

What is a SODIMAS NG controller?

NG refers to the generations of SODIMAS controllers prior to QI Touch: NG02, NG12, NG120 and NG240. They drive the motor, doors, signalling and safety devices of the lift. NG240 is the most recent and the most represented in the KMY catalogue.

What is the difference between the NG12 variants?

The variant depends on the drive type and associated drive: two speeds without drive, Altivar ATV31, ATV58, ATV71 in 5.5 or 7.5 kW, V3F10, or hydraulic version. Wiring and boards differ by version: identify yours before ordering.

Can you switch from an asynchronous motor to a gearless machine on an NG?

Yes, SODIMAS provides a conversion kit to a synchronous machine driven by a Fuji FRENIC Lift drive. It involves adding a bypass contactor in the power cabinet, connecting an encoder board and reworking the brake voltage. Above 11 kW, an additional contactor and rectifier are required.

How many levels does an NG controller serve?

The motherboard documentation dated 2012 announces up to 24 levels, adjustable depending on the type of controller, with 1 or 2 accesses, with multi-door management. Counting can be incremental or absolute.

Should an NG be replaced or modernised?

Both are possible. Like-for-like replacement preserves the existing wiring and remains the fastest. A modernisation to QI Touch brings the touchscreen, guided setup and connectivity, but is an intervention of a different scale. KMY can price both options.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote