Skip to content

ORONA · Platform

Orona ARCA controllers — boards, signalling and parts

ARCA is the control system developed by Orona. It exists in two main generations in the installed base: ARCA II, then ARCA 3, the latter notably available in a gearless version.

Configuration and diagnostics are carried out with a dedicated configuration tool, also called a maintenance terminal, which allows setting the unit’s parameters and assists troubleshooting.

The ARCA references in the KMY catalogue are mainly divided between electronic control boards and signalling — buttons, landing plates and displays —, to which are added the selection devices in the shaft.

Technical sheet

Technical specifications

Generations
ARCA II · ARCA 3 · ARCA 3 gearless version
Configuration
Orona configuration tool / maintenance terminal · Setup and troubleshooting aid
Selection and position
CB and CS type magnetic fingers (ARCA 2) · CDB magnetic finger (ARCA 3)
Signalling
3G range buttons, with engraving and braille marking · Landing plates · Position indicators
Families in the KMY catalogue
Electronic control boards · Buttons and plates · Power supplies · Key-operated devices

Installation architecture

Parts are divided into four zones. Identifying the zone concerned is the first diagnostic reflex: it immediately narrows down the possible references.

Control cabinet

ARCA control boards and associated power supplies. The generation — ARCA II or ARCA 3 — determines the board reference.

Related parts: Arca board · power supply · cabinet

Shaft and selection

Magnetic fingers handle position detection. Their type differs by generation: CB and CS on ARCA 2, CDB on ARCA 3.

Related parts: magnetic finger · sensor · bistable

Car and landings

3G range buttons with engraving and braille, landing plates and position indicators.

Related parts: Arca button · plate · display

Machinery

The gearless version of ARCA 3 comes with a direct-drive machine and its encoder feedback.

Related parts: winch · encoder · brake

Points of attention

  • Determine the generation before any order: the CB/CS magnetic fingers of ARCA 2 are not those of ARCA 3, which uses the CDB type.
  • Control boards are specific to their generation and carry settings: a blank board does not replace a configured board.
  • The Orona maintenance terminal is needed to restore the configuration after replacing a board.
  • On 3G buttons, note the engraved symbol and the presence of braille: these elements fall under accessibility rules and are not optional on controls intended for users.
  • Send a photo of the board and its markings: it is the most reliable way to tell apart two generations of similar appearance.

Get a quote

State the part reference if you know it, the number of levels and accesses of the unit, the type of wiring and your wilaya. A photo of the part in place and its markings confirms the match. KMY confirms the final price, availability and delivery time in Algeria.

Search all Orona ARCA parts in the catalogue ↗

Source of the specifications: Orona ARCA II controller configuration tool manual, standard 0466035 version 6 (26/11/2015), and ARCA 3 Gearless documentation. Data reproduced for information only; only the manufacturer’s documentation is authoritative. Specifications may change between versions.

FAQ

Frequently asked questions about Orona ARCA

What is the Orona ARCA controller?

ARCA is the control electronics developed by Orona for its lifts. It manages calls, drive and door control, signalling and safety devices. Two generations are commonly encountered: ARCA II and ARCA 3.

What is the difference between ARCA 2 and ARCA 3?

Beyond the control boards, which are specific to each generation, the selection devices differ: ARCA 2 uses CB and CS type magnetic fingers, ARCA 3 a CDB magnetic finger. ARCA 3 also exists in a gearless version.

How do you configure an ARCA controller after replacing a board?

Orona provides a configuration tool, also called a maintenance terminal, which allows setting the unit’s parameters and assists diagnosis. Its use is necessary to restore the configuration after replacing a control board.

Which buttons equip ARCA lifts?

ARCA installations commonly use 3G range buttons, offered with symbol engraving and braille marking. Landing plates exist in several finishes and compositions depending on the number of controls and whether there is a display.

How do I get the right ARCA reference?

State the generation (ARCA II or ARCA 3), the reference shown on the part to replace, the number of levels of the unit and your wilaya. A photo of the part and its markings allows KMY to confirm the match before ordering.

A reference to find? Send us the marking on your part.

Let’s talk. Our teams reply within 48 hours with a first estimate.

Request a quote